Servo Arm length Measurement request
So i've been playing with turning the servo ends in and out on the aileron and elevator servos to find a nice balance and now I've lost track on where they are at. I would like to reset the length as...
View ArticleClik here to view.
Align Trex 700e V2 parts pick your part
The pictures attached are what I have left from a 700e V2 kit I took some parts from. Before I put it on ebay and enrich them further :) If you see anything you can use just PM me or even email me...
View ArticleAm I mad ? probably
In hover training mode I would like to be able to flip the heli. However when you do this the logic of the controls change. Am I the only one to find:D this an issue. Regards Mostly not inverted so to...
View ArticleJoined the 'forgot I wasn't in idle up mode inverted auto' club today
Learning inverted, landed to tweak expo on the tail. Took off and was surpised when the engine dropped to idle while inverted. Thanks to altitude I rolled level and landed normally. I laughed all the...
View ArticleHow to get vbar4.0 to work on win7 ?
I cant get an older vbar 4.0 to work with my win7 computer. I have a newer 5.2 with driver working on same computer. any ideas ? thanks martin
View Article325mm Spinblades Asymmetric - First Impressions
I picked up a set of these (two actually ... just in case my buddy wanted a pair) on Friday and finally got a chance to fly with them today. All I can say is that these are an excellent choice for a...
View Article7200bx elevator and pitch switched
For some reason my elevator stick works the pitch and my pitch(throttle stick) works the elevator. Everything else is fine. My transmitter is dx6i, and I have tr's swash set to 90* 1 servo with all...
View Articlekdbb blades????????
hey guys.. i just bought 2 pairs of kdbb blades... the new pink ones and orange ones...well I've been using the stock bullet blades which i love..and the micro carbon blades..which are also good...but...
View ArticleClik here to view.
F/S THREE LIPO 6s BATTERIES
I have for sale, three used lipo batteries. one is a Zippy 6s, 5000mah, 40c. Approximately 25 cycles and always balanced. The other two are Voltz 6s, 5100mah, 45c and also about 25 cycles and always...
View Article600e pro/dx6 gain Q.
Hey all,,just setup the new 600pro (flybar verison).with a DX6i Its was the new gp900 rec/tail gyro... Q.what % gain did you need in normal and st-1.. I know the older gp780 would work around 70 %...
View ArticleWhich telemetry for XXtreme?
Hello, I'd like to understand what happens during the flight :lol:.... what system do you suggest? Thanks to all,best regards!:thumbup:
View ArticleMicroheli Frame to X-Frame differences and upgrade
The new X frame's main benefit is the rear mounted anti rotation guide. This corrects a small issue with the swash not rotating around it's natural center causing a twist when doing certain maneuvers....
View ArticleXXtreme Motor Oiling
As far as I am aware all Scorpian motors should be oiled every 5-10 flights, not seen anything in the X's manual relating to oiling etc. Any one know the drill with the Mikado supplied Scorpian ?
View ArticleMini Titan in a MD500 Scale Fuse
Looking at the Smart Model MD500 for my Mini Titan, does anyone know wether it will fit? The Fuse is a 450 size but the mini titan is not a true 450 model....
View ArticleClik here to view.
How to open align motor
Hi!! I've bought a align 450 mx 1700kv to convert my 450 sport to 6s. Besides being surprised by the extra strength these magnets have, i'm puzzled that there is no c-clip or grub screw anywhere in the...
View ArticleDX7s with Satellite
Howdy, I got the DX7s with the Receiver/Satellite combo. I'm currently only using the satellite with a 3GX system and want to buy another satellite because the 3GX supports two satellites. Is it just a...
View ArticleClik here to view.
2 RTF TREX 700 FLYBARLESS BEAST X !!!!!
TREX #1 let me start by saying this is a awesome machine align blades beastx ver 3 align 610's on cyclic and throttle align 650 on tail specktrum AR7600 reciever with satilite. Also, align 2n1 with...
View Articleneed help finding a replacement part
OK I can't seem to find a feathering shaft/spindle to replace on my gohbee stinger head the size is 6mm x 92mm with 4 mm bolts the raptor spindle is 89mm its too short and it seems all the spindles I...
View Article