Dx6i
Looking to buy a spektrum Dx6i (or Dx7s if the price is right) Please let me know what you have. Shipping to Mesa, AZ. Thanks
View ArticleLoaded Compass 6HV with SK720
I plan to move in the next month or two so I need to start clearing out some stuff. I'm selling a great condition Compass 6HV. Here are the specs. Compass 6HV FBL Fusuno 2mm Carbon Frames Fusuno Red...
View ArticleClik here to view.
Futaba 12FG w/FASST Module
This is a Futaba 12FGH that will also be included with a Futaba FASST module that was purchased seperately. This radio has very little use on it (~4-6 months) and has always been kept in a case inside...
View ArticleDesert Palms, CA hobby shops
Any good heli hobby shops in the desert palms area, heading there this weekend for work. Thanks
View ArticleHow Many Grams of Thrust Does The mSR X Produce?
If anyone with a digital scale would be so kind as to measure the AUW of a stock mSR X. (HH says 31g) Then press 'tare' while your skids are securly taped to the scale table and slowly increase the...
View Article8917 vs. 8717 servos for cyclic??
So I bought a set of 8917 HV servos for cyclic on my SAB Goblin. I'm just trying to figure out if there's any reason to upgrade to the 8717's HV's. They are almost $200 more for a set of three, but I...
View ArticleNoob - Looking for RTF electric. Ideas?
Complete and utter (clueless Noob. Just ordered a Double Horse 9116 but know its a basic starter and not the "real" thing. Cost was perfect however to see/allow me chance to become addicted. First heli...
View Articlemicrobeast setting/android
just had a idea and dont know if its posible but can the mb software work with a droidx phone?
View ArticleBTW For those who are curious tail blade accuracy
For those of you who think your KBDD blades are balanced better than MSH tail blades, I just got a scale accurate to 0.01 gram. The KBDD blades I tested were accurate to 0.02 grams. The MSH 3K blades I...
View ArticleClik here to view.
Carnage after BL crash!!!!
I was finally able to get out and put my new BL setup(HP05, sr120 tail and Hyp.550mah) to the test. Everything was going okay,until I was on my last pack and I dumb thumbed hard into the ground. This...
View ArticleLearning to fly my first Quadricopter
I'm new to the quad copter scene and building my first one now. Anyone with experience can enlighten me as to the characteristics of flight please. Does it fly like the traditional helicopter with...
View ArticleSD 10g with 3g on a gaui 425
Hello I am haveing problems with this set up have been for months i feel lik this :arggg: OK i have done the finless bob on the servo horns. all the belcranks are 90 and the swash is level. today i...
View ArticleBlue Blink with Throttle Lock?
Not sure...but from what I have seen in videos my mcpx should not be blinking when i throttle lock to do inverted. am i right?
View ArticleClik here to view.
2 TP 5000 6s 65c 10 flights on them
2 TP 5000 6s 65c sync charged with a hyperion 720 duo charged At 1amp per cell. Only 10 easy flights on them ,still new as you can see in the picture there flat. Just sold my 700 and dont need them. I...
View ArticleHow much weight will have a noticable impact?
I recently got set up with a scale good to 0.01gram and a Koll Blade balancer so I can even get the CG on my blades perfect. The tail blades I've tested so far are pretty darn close 0.01-0.02 gram...
View Article4525 520 is it ok with GEN ACE 2 6s 5000 30c to make 12s
Has anyone FLOWN this combination 4525 520 with gen ace 2 6s 30c to make a 12s, I ask because I hear so much that the gen ace are rated lower than what they are and wanted to no if someone has this...
View ArticleClik here to view.
align 700 f3c rotor head
So I have built the new verision of the rotor head, however, I am assuming as compared to other helis, that zero pitch is when everything is equal and straight on the rotor head. However when the new...
View ArticleClik here to view.
Wiring question
So I have 20gage wire throughout the power connections now I'm wondering if I should down size to 22 from esc to battery and 24 from esc to 3in1 just to loose some weight and maybe it'll clean the...
View Articlevbar mounting position/orientation
Sorry if this has been asked before but can the mini vbar be mounted diagonally? I'm planning to mount the unit in the back of the embla facing outwards towards tail rotor.
View Article