Clik here to view.
Logo 400 SE spec analysis
Hi, I've a attached a spec analysis screenshot showing my spikes well under the yellow line, maxing between 336 and 350. This is where I'm at after rebuilding the tail with a carbon tail box and new...
View ArticleIs it possible to remove an EC5 connector?
I need to reroute a wire so I need to remove a bullet from an EC5. I tried a few things... no luck. Is it even possible to remove the bullet without damaging the housing? Or do I need to cut it off and...
View ArticleClik here to view.
Attempting Paper Canopies
Paper Canopies seems to be pretty popular over in the MCPx section. Now I am just an IT, PC's, MAC's, Networks that kind of stuff I make no promise be an artist. But I wanted something different than...
View ArticleGoing to try some AEO blades
I don't know anything about the brand but going to give them a try. Just placed an order for 2 sets of these, $13 shipped. http://www.ebay.com/itm/AEO-RC-Blade...#ht_1229wt_856 Will update when they...
View Articletrex 500 setup
ok i have it built,i have the receiver and 3gx hooked up,,move throttle all three servos go up and down,aileron servo moves correct,,elevator servo moves correct,they just don't work together in the...
View ArticleSwitched back
Went with the micro heli frame. Looked great but had porposing issues. Then I discovered how weak the rear portion is. Broke both the rear carbon sides and the little nylon tail boom holder. I was...
View Articlenew build questions...
taking the leap into the 700E land and figured no where better to ask then here. wanted everyones input on what consumables to stock up on for an upcoming 700E build. Locktight, CA, grease, two sided...
View ArticleGyro
Just Ben flying the mcpx for a week or so haven't got the gyro right on my dx6i what do you guys have yours set at let me no pleas
View Article4.7 Firmware?? anyone have the instructions?
Ok I have the 4.7 x firmware I know how to flash the board but does anyone have the instructions on how to set up after that for the pots and etc. I have the manuals for the v2.2 "KKXXKR Settings...
View ArticleTreed, for a month and a half...
...went through two soaking rains before it finally fell from it's perch yesterday. I picked it up off the lawn in a pouring rain yesterday morning on my way to work. I let it dry all day yesterday and...
View ArticleNew MCPx Issues
Just got my mcpX and DX7s, I updated the firmware on the DX7s, downloaded the mcpX model from Spektrums site and tried to test swash movement out. The blades at mid stick have a tad of pitch to them,...
View ArticleWalkera # 59 DQ Coast Guard RTF with fenestron
http://helifreak.com/showthread.php?t=377734
View ArticleClik here to view.
got everthing i need now to build
well everthing came in the mail 2 day vbar ,spectrum dsmx sats ,hyperion sensor ,ec5 series red tail blades went over to westeren robotics and picked up super bec.I got my servos installed using...
View ArticleWalbro felt clunk for Nitro?
I loved the idea of the OMI fuel magnet and also the way it functions. Unfortunately I've had 2 disintegrate on me and the last one lasted less than 6 months. I keep the fuel tank full and using the...
View ArticleLoss of heading hold?
So I have a weird issue were I can use rudder to change the speed of the tail but it will not hold heading. On the bench I can rotate the heli and the motor does not increase or decrease speed, but it...
View ArticleNew 450 pro V2 won't auto rotate
I just got done with basically everything but the tail on my new 450 pro V2. Once I put on the main gear I noticed that it won't auto rotate freely. The bolt at the bottom is not too tight and...
View ArticleClik here to view.
Assorted 2.4ghz tx/rx sets
these things take up too much room on the shelf so i moved onto a DX7. FREE if you pick them up; otherwise, it'll be the cost of shipping. Hobby King HK-T6A V2 / HK-TR6A V2 Exceed FS-CT6A / FS-R6A+sat...
View ArticleAnyone tried both 2221-6 and 450MX ?
I am using 2221-6 /13T. But I heard align 450MX /15T have similiar performance or exceed. Anyone tried both? I'd appreciate sharing information.
View ArticleSlop in the main @ blade grips
Feathering shaft and bolts are nice and tight, with new Trueblood dampeners, and I still have some slop / play in the grips. Not a whole bunch, but a little bit. Anybody have any fixes for this they've...
View ArticleClik here to view.
425mm V2 Carbon Fiber Blades for 500 size
I have a pair of used V2 3D Carbon Fiber Blades, Had this on my Trex 500, Flew Great!!! Dont need these anymore.. Has normal wear and a few nicks on them, nothing that takes away from performance.. See...
View Article