...Too Much Maintenance
I fly my MSR VERY hard with little to NO crashes and Im tired of buying parts all the time because they wear out. -Flybar...the center hole wears oval and flying gets sloppy -Tail boom/motor...
View Article550 Battery that fits in stock location
Is there another 550 mah battery out there like the one below that fits in the stock location and uses stock connector? http://www.amainhobbies.com/product_...ack-37V-550mAh
View ArticlemCPx version 2 Motor Bind
Hello All, I was wondering if anyone had any suggestions. I just purchased a mCPx version 2 and setup my dx6i controller with all the preferred settings. One of the things I first noticed is the main...
View ArticleClik here to view.
2 TP 5000 6s 65c 5 flights on them
This is my second set of 2 TP 5000 6s 65c. I was going to keep these for a 500 build but went a differant way so dont need anymore. They were sync charged with a hyperion 720 duo charged At 1amp per...
View ArticleSpinning 120
My brother just bought a 120sr, it hovered good for a few minutes, then all of a sudden it started spinning around counter clockwise, thats all it will do, checked it out looked it over can't see...
View ArticleClik here to view.
RJX Flybarless Head Trex 500
NIP RJX Head for Trex 500 + align linkages, linkage balls (see pic), and feathering shaft sleeve ( increased stiffness).$80 firm shipped to CONUS. Thanks for looking Attached Thumbnails Â
View ArticleClik here to view.
Trex 450 S/SE Flybarless Head Align
NIP Trex 450 Align flybarless head from Grand RC-- does not fit TREX 450 Sport or Pro. Also comes with linkage rods and attachment for head so that a flybar can be used to help set pitch.$90 firm...
View ArticleCOG question???
The swash thread got me wondering about my COG. After I level my swash and set my pitch, I still have to shorten the front elevator link one full turn to get it hover level with minimal stick input....
View Article700 head and blades on a 600E
I asked this on the 600E forum but no answer. I got a 600E on a F3C (700 size) type fuselage that the previous owner did not fly, he installed a 700 head over the 600 swash and washout links and 700...
View ArticleSlow servos with ZYX Gyro
I have a HK500 with the ZYX gyro. I went through the setup a couple times to make sure I have it set right. I re-initialized the gyro and when I move the cyclic, the servos move slow. My collective...
View ArticleClik here to view.
Avantgarde 600 Spektrum AR7200BX and SAB blades.
The new Spektrum AR7200Bx units have arrived in Australia. I had hoped they would be available before I finished ny heli but I had to fit a separate receiver and BeastX to get airborne on Christmas...
View ArticleHorizon Hobby won't answer my emails
I keep hearing about how great Horizon Hobby's customer service is. I remember one time they got me a new ar6400 when I had a bad one. I think I had to call them on the phone a few times to get it....
View Articleim so dumb
ok, i was setting up my brand new v bar that i bought off here a few days ago on my new fusion 50. i was trying to get it to initialize on the pc software but it didnt. i just sat there at initializing...
View ArticleInexpensive flybarless
Can anyone recommend a cheap flybarless system? I can't see myself paying more than about 200 for them.
View Article2s LifeP04 with the new 130a?
So I've been looking around for a buffer/backup 2s LifeP04 that I can use for this purpose...I found this pack and am wondering what you guys think... Its really small and would be a very clean setup,...
View ArticleMaintenance?
Hi all, is there are place to look on here for heli maintenance? I read somewhere about oiling electric motors, is that right? And also lithium grease on belt? Anything else I should be doing I would...
View ArticleWTS Thunder Tiger Raptor 90 3D with Hitec Telemetry
Hi, i've been flying helis for a while and now with my work and my gf who is'nt in those things i dont find the time to fly anymore. I might come back one day but i'll get a lipo heli. So here it is,...
View ArticleNew gyro / tail wag/bounce
So I thought my gyro was going bad. This is the stock gyro on the blade 400. I had this tail wag, but only when I gave minor rudder command and let go (let the stick center itself). Otherwise it hovers...
View ArticleBroken Bind Button
Hi, Has anyone ever broken the bind button on the Esky 4in1? Is it possible to solder it back? :arggg::arggg: Thanks
View ArticleO ring help!
I have searched and searched and searched and cant find the write up of the 001, 002, and 003 o ring install. i just got mine and also why people put o rings behind the circuit board.
View Article